Life in the Village and beyond, based around the interests of my life.

Life in the Village and beyond, based around the interests of my life. Sunset at Telegraph Point.

Friday, March 30, 2012

An Elegant Jelly Cabinet - Construction Part 9 - The End is in Sight

Lots of Little Bits

The door frame is finished and the bottom rail repair came out very well.  Clamp and glue time - as the door frame is fitted to the front edges of the carcass.


It is time to start adding the various parts to bring the cupboard to completion.  Before this, however, I like to give the straight carcass a complete sanding outside.  It is much easier to do this before the top and the mouldings go on.  Of course there will be final sandings later, but since this won't take long I'll do it now.


The picture on the left shows the difference that this initial sanding makes.  The ripple marks from the power jointer can be seen towards the top left corner.  The sander is an old German Metabo  RAS - still going strong.  Today was a magnificent early autumn day, so out front of the shed was the place to be. Blissful it was!


 
Now is a good time to break those sharp edges with a sanding block.  Here I am using 180 grit. The sun came out onto where I was working - look at that beautiful timber.


 This is the back panel - inside and outside. Note the rebated edges so that it can slide into the back of the cabinet from the bottom.  The sun came and went as I worked - what a joy.

I glued the top to the  sanded carcass and set it aside to dry.  Should be set by tomorrow.  Meanwhile it's time to attack the door.


Making the Frame and Panel Door




The frame for this door is quite narrow, so I have decided to use an open slot mortice on the stiles, and tenons on the rails.  This should give me a larger glued area and a stronger joint - even though the end of the tenon will be visible at the corner of the door. The frame pieces already have the groove cut previously, so part of this has to be removed for the joint to work.

I could have chosen to mitre the face edge of the groove, but decided to keep it simple in keeping with the cabinet.  I now wish I had, because I would have given it a little more thought, and avoided the mistake that I went on to make.

The astute reader will see the makings of the "Oh Shit!" moment in the layout of the picture above.  If you don't see it yet, be patient and it will be revealed.


I chose to cut the mortice first, and good old Spear & Jackson sawed the cheeks, and a little jewellers saw cleaned out the waste.  Spotted the blue yet?


Chisels to the rescue to tidy up the saw cuts and square the bottom of the mortice.  I like to undercut the bottom as shown in the last picture - right - as this leaves somewhere for the glue to pool, and guarantees a flush fit.  That middle chisel is a slim tapered Mathieson, the only one I have - wish I had more in different sizes.  It is perfect for getting into the mortice to gently adjust the interior by removing any high spots.


OK - time to cut the tenon.  Measure up against the mortice - (that middle picture is a give-a-way to the clanger that is about to happen).  Cut carefully and fit.
Look at that last picture - right - almost perfect .............................................. almost !!!!!!!!




AAAAAARRRRRRRRRGGGGGGHHHHHHHHH!!!!!!!!!!!!!!!

.... and it was looking so good up until then.

Another fix is necessary.  I'll still glue it up and add an appropriate sized plug to fill the hole.  Lucky it's on the hinge side of the door, so will rarely be seen.

The mistake was mine from the get-go, and it happened because I was tired when I started this, and didn't think it through.  I was smart enough to stop at this point and do something simple before calling it a day.

I decided to add some dowels to the middle of the tops of the feet, so that they will register easily with the bottom corners when they are glued in position.

It was a daggy old piece of dowel, but won't ever see the light of day - so - good enough!

Rightee-o, one more post and this will be finished.  Can't wait.

LOML is hounding me about starting work on the repairs to the house gables.  Guess that will be next.

May your days be joyous and your mistakes small ....

 ............................ and happy woodworking to all .......

6 comments:

  1. Replies
    1. Yep, I was absolutely "in the groove" while I was doing the door frame. The bees were buzzin', the birds were singing, the saw cut sweetly and the chisel was soooo sharp it just shaaaaved those curlies. Pity I wasn't paying attention to the joint.
      No matter, I'll do better with the rest of the door. I have enjoyed this project immensely, and am keen to see the finished cupboard.
      Thanks Ray ....
      Cheers
      Tom

      Delete
    2. Oh Tom, It's still a wonderful piece. I think it is just one of those things - I know I have a few problems with my joints these days. Warm baths and glucosamine are what I would recommend. Just keep swimming.....just keep swimming!! Luv M xx

      Delete
  2. Warm baths and glucosamine - great idea. Best I could do yesterday was a hot shower, cold beer and some time on the Uke.
    Thanks Maudy for your kind words.
    See you soon.....
    Tom

    ReplyDelete
  3. Hi Tom,
    You seem to be doing a great job so far minus the whole in the door hing with the making of your cupboard. I love your step by step commentary and your swearing at the appropriate times in your write up. You crack me up some times with your humor, I love it.

    Keep up the great woodworking and I am looking forward to seeing the finished cupboard in your blog.

    Love from Natalie

    ReplyDelete
    Replies
    1. Thanks Nat,
      once a teacher - always a teacher I suppose. Although I hardly ever swore in the classroom - (hope none of my ex-year 12's read this - hee hee)
      Your friend
      Tom

      Delete